One Trip is All it Takes

ChimneySaver 1Trip! CrownMix is the premier cement mix specifically designed for pouring chimney crowns in one day. 1Trip! CrownMix is formulated with proprietary materials that enhance workability, achieve rapid initial set times, resist water penetration, increased freeze/thaw resistance, provide corrosion inhibitors, increase impact resistance, increase flexural strength, and promote self-healing of micro cracking.

Packaged in a convenient 5-gallon pail, it's designed for easy rooftop mixing in its original packaging with a spiral mortar mixer drill attachment and sets in approximately 1-2 hours, helping you complete the job faster.

Product Benefits

• Enhanced Early Workability
• Rapid Initial Set Time
• Built-in Water Repellency
• Advanced Freeze-Thaw Resistance
• Integral Corrosion Inhibitors
• Triple Fiber Reinforced
• "Mix in Bucket" Design
• Self-Healing Technology

Instructions

• Coverage Rate: Approx. 0.4 cubic feet. per 50 LBS Bucket
• Application Temperatures: Minimum 50° F
• Curing: Under typical conditions, forms may be removed at approximately 2 hours. Curing should continue for a period of 5 days in warm weather. 
• Cleanup: Soap and water while product is still wet 

WARNING: This product can expose you to Crystalline Silica-Quartz, which is known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov.

HeatShield’s hybrid “Cerfractory” technology combines the strength of a high-fired ceramic with the heat resistance of high temperature refractory cements. HeatShield Cerfractory Flue Sealant when used with CeCure Sleeve is certified to UL 1777- Standard for Chimney Liners by Intertek. HeatShield has been tested to ASTM C199 Standard Pier Test for Refractory Mortars and is rated “Super-Duty”. It exceeds both IRC and NFPA code requirements, which specify medium-duty.

It can be used to reline masonry chimneys with the addition of the CeCure Sleeve, provided the HeatShield Cerfractory Flue Sealant mix plus the CeCure Sleeve achieve a total minimum of ½ inch lining material thickness. In suitable masonry chimneys, HeatShield Cerfractory Flue Sealant may also be used to repair missing or defective mortar joints, or it can be “slip cast” over the entire surface at an average thickness of 3/16 inch (1/8” min.). HeatShield Cerfractory Flue Sealant with CeCure Sleeve is considered an “all fuel” chimney liner. For use only with residential chimneys that service Category I gas-fired (natural gas or propane), Type L vented oil-fired and solid-fuel-fired appliances.

WARNING: This product can expose you to chemicals including quartz, which is known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov.

PCR is a revolutionary product designed to completely remove 3rd degree glazed creosote from flue tiles or stainless steel chimney liners. When PCR is applied, it dissolves the creosote and absorbs it. As it absorbs the creosote and dries, it loses its adhesive properties and falls off the sides of the flue tiles. Any remaining PCR can be easily removed by chimney sweeping. PCR can be applied by brush in areas that are easily accessible, or with a specially designed tool that can be pulled up through the chimney by a winch. To remove glazed creosote in smoke chambers, PCR can be applied with SaverSystems’ Smoke Chamber Sprayer. PCR should be used where glazed creosote is present in order to eliminate the dangers of chimney fires.

• Completely removes 3rd degree glazed creosote
• Eliminates the need for dangerous and potentially destructive cleaning methods
• Easy to apply and remove

WARNING: This product can expose you to chemicals including quartz, which is known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov.