Read the Label - Fireplace Mortar

HeatShield Fireplace Mortar is dry-mix refractory mortar designed for use in indoor residential fireplaces and masonry heaters. Because it is a dry mix, it can be mixed for dipping, grouting, and laying firebrick. After firing (use) the mortar becomes non water soluble. This mortar is extremely sticky and thermal shock resistant with service temperatures tested up to 2550°F (1399°C).

INSTRUCTIONS

READ AND ADHERE TO ALL SAFETY PROCEDURES IN SDS

Surface preparation

  • Only apply to structurally sound, stable, clean, dry surfaces.
  • Application surface may be damp. Remove any excess water. Pre-wetting the surface may help minimize joint shrinkage.

MIXING

For grouting mortar:

For use with the PriorFire Retrofit Fireplace System. Use 3oz of water for every level scoop of dry mix (scoop provided in pail). To grout both side walls of the PriorFire retrofit: place 3 ¾ cups (30 oz) of clean, potable water in clean suitable mixing container. Add 10 level scoops of dry mix to water and mix manually or with small mixing paddle to a smooth, lump free consistency. Let mix stand (slake) for 3-4 minutes and remix briefly. Add small amounts of additional water if needed to achieve smooth grouting mortar. Do not over mix. Wash tools immediately after mixing. Pot life is about 1 hour. Pre-wet assembled brick wall using a sponge and clean water. Push grouting mix deeply into each sidewall joint with a rubber faced margin trowel. Scrape off excess mortar with a putty knife and wipe grouted wall with clean water and sponge until wall is clean.

For Dipping Mortar:

  • Place 2.5 quarts of clean, potable water in a clean suitable container.
  • While mixing slowly, add 20 lbs. of dry material.
  • Using a drill and paddle mixer at lowest speed (~300 rpm), mix to a smooth, lump free consistency.
  • Allow mortar to stand (slake) for 3-4 minutes. Remix briefly. Add only small amounts of additional water to adjust consistency.
  • Wash tools immediately after mixing.
  • Pot life is approx. 1 hr. Remix if mixture becomes heavy or stiff. DO NOT ADDMORE WATER. DO NOT RETEMPER.

For Trowel Mortar:

  • Place 1.75 quarts (7 8 oz cups) of clean, potable water in a clean suitable container.
  • While mixing slowly, add 20 lbs. of dry material.
  • Using a drill and paddle mixer at lowest speed (~300 rpm), mix to a smooth, lump free consistency.
  • Allow mortar to stand (slake) for 3-4 minutes. Remix briefly. Add only small amounts of additional water to adjust consistency.
  • Wash tools immediately after mixing.
  • Pot life is approx. 1 hr. Remix if mixture becomes heavy or stiff. DO NOT ADD MORE WATER. DO NOT RETEMPER.

APPLICATION

A joint of 1/8” or less is recommended.

COVERAGE

For grouting the PriorFire retrofit, each bucket will grout the sidewalls of two (2) units. 30 to 40 firebrick per 20 lbs. at 1/8” mortar joint.

STORAGE

Store left over dry material in well-sealed container in a cool, dry place. Shelf life is approximately 1 year, depending upon storage conditions.

Notice: There are no implied or express warranties made with respect to this product. SaverSystems shall not be liable for personal injury, incidental or consequential damages, indirectly or directly sustained. Before using, the user shall determine the suitability of the product for its intended use and the user assumes all risks and liabilities that may arise in connection therewith.

PRECAUTIONS

FIRST AID: Never give anything by mouth to an unconscious person. If inhaled: Remove person to fresh air. Obtain medical attention if breathing difficulty persists. Skin contact: Remove contaminated clothing. Wash affected area with water. Obtain medical attention if irritation develops or persists. Eye Contact: Immediately rinse with water for at least 30 minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Get immediate medical advice/attention. If Swallowed: Rinse mouth. Do NOT induce vomiting. Obtain medical attention.

Warning: This product contains crystalline silica and aluminate cement. The dust is mildly irritating to eyes and mucous membranes. Avoid contact with eyes and skin. If contact is made, flush with generous quantities of lean water. Wear safety glasses and OSHA or NIOSH approved respirator. Inhalation of crystalline silica can be harmful to health and may cause delayed respiratory disease and lung injury (silicosis). Crystalline silica is a known human carcinogen and if inhaled from occupational sources can cause cancer. Keep out of reach of children. Do not ingest. Consult SDS for further information.